General discussion • how to boot from m.2
dear all i just bought raspberry pi compute module 5 and Compute Module 5 IO Board and i install Samsung 990 PRO 1TB with Heatsink NVMe Gen 4 M.2 Internal SSDnow the challenge is how to boot from NVMe...
View ArticleClik here to view.
Beginners • Suggestions on Workflow, Hardware, and Software for Voice Chatbot...
Hi, I am Roberto, a PHP and JavaScript software developer. I have been exploring the world of Raspberry for a few weeks as I aim to create a voice chatbot by integrating it with my already functional...
View ArticleDevice Tree • Assistance with Device Tree Overlay for GPIO-Based I2C and...
Hello Raspberry Pi Community,I am working on integrating a Goodix GT9271 touchscreen controller with my Raspberry Pi using a GPIO-based I2C bus. The I2C bus is connected to GPIO10 (SDA) and GPIO11...
View ArticleTroubleshooting • Samsung ML-1860 printer on PI 5 and Cups 2.4.2
Hello. I am new user of Raspberry pi. A one week ago I installed my printer ML-1860 and it works great. Unfortunately after actualization CUPS the printer stop working.. I tried a lot tricks which I...
View ArticleTroubleshooting • Unable to get CM4 to use ant2
As far as I can tell, the only change I'd need to do is add Code: dtparam=ant2 to Code: /etc/firmware/config.txt and then reboot. But this doesn't appear to actually change which antenna output is...
View ArticleClik here to view.
General discussion • Remote to Pi at another location?
Hello! This may be a dumb question...I am currently connected to my Raspberry Pi Zero via PowerShell - Logging in as Username@192.168.0.**I want to send it to my cousin at another location - How will...
View ArticleCompute Module • CM5 power issue
Hi,I just got a CM5 8gb, 32gb Wi-Fi and a CM5 io board.However im experiencing a problem, I flashed the pi with pi os and when I try to power it up from the official psu no lights come on, same with...
View ArticleSDK • I2C ssd1306 example
I must be doing something wrong, but I'm not seeing it.I have the ssd1306 example working, but only when I redefine PICO_DEFAULT_I2C.I'm showing only the bits I changed. This code works:Code: #ifdef...
View ArticleTroubleshooting • Raspberry Pi 5 bootet nicht mehr.
Hallo zusammen,nach einem rpi-eeprom-config habe ich den BOOT_ORDER auf folgenden Wert eingestellt. Boot_ORDER=0xf614.Ich habe leider keine Grossbuchstaben bei BOOT_ ,sondern Boot_ verwendet.Nun...
View ArticleTroubleshooting • Got a Kamvas pen display need drivers
Hello Everyone, We've been gifted a very nice Kamvas Pro 16 Drawing table with a screen built in. We had a little play yesterday and most of the features work out of the box. What doesn't work are the...
View ArticleCamera board • Issue of OV5647 camera in opencv
i have ov5647 camera module with raspberry pi 4/4gb ram. I am working on face detection code in it but when i try to access camera using opencv it shows black screen in preview where if I run Code:...
View ArticleRaspberry Pi OS • Some interesting questions about Linux (RpiOS) NTFS drivers
First off, I know the general advice is "Don't do that!". Don't use NTFS under Linux. Needless to say, we do it, because we need Windows interoperability (**). So, don't bother saying "Don't do...
View ArticleGraphics, sound and multimedia • ilitek 9341 setup issue
Hi all. I have recently bought an ili9341 TFT display on Amazon https://www.amazon.nl/-/en/dp/B07QFVBPM ... asin_title to replace the https://www.amazon.nl/-/en/dp/B078J5TS2 ... title&th=1 which...
View ArticleTroubleshooting • Cannot SSH when HDMI LCD is connected
Hi,I’m having trouble connecting via SSH when I attach an LCD (https://pl.aliexpress.com/item/10050067 ... pt=glo2pol) screen to my Raspberry Pi 5. When I use a different LCD monitor with the same...
View ArticleTroubleshooting • Raspberry Pi 5 cannot get to boot settings
Hello, I am new to the Pi ecosystem but am loving the Pi 5 as a retro gaming console. for the first couple of weeks it ran fine but for the last couple of days whenever I turn it on I get the white...
View ArticleTroubleshooting • Pi 5 stopped booting with 8 green flashes - not fatal
I just want to make a new post here as the one the google result went to is locked:viewtopic.php?t=359355I have a Pi 5 and for whatever reason stopped booting, I initially kept getting a solid red...
View ArticleGeneral discussion • Installing openMPI 5.0.6 on a Raspberry Pi
Has anybody got openMPI 5.0.6 installed on a Raspberry PI?I've tried several tutorials but haven't been successful in getting it to work.If you could please point me to a working tutorial/how to, (or...
View ArticleTroubleshooting • Pi 5 no longer has functioning wifi after latest update
Ran an update. Rebooted. Network manager shows two red x's in the taskbar. Doesn't see any wifi available. Any help would be appreciated. ThanksStatistics: Posted by penciltester — Thu Dec 26, 2024...
View ArticleFrançais • Onglet Chrome apparait automatiquement
Bonjour à tous j'ai un projet ou je dois configurer mon Raspberry pi 4 de sorte à ce qu'au démarrage il y a une fenêtre chrome qui apparait avec 2 onglet diffèrent ( 2 site différents ) et que tout...
View ArticleBeginners • Raspberry Pi 5 Graphics , good ?
What about Raspberry Pi 5 's graphics . I feel it isn't so powerful ? I have a RbP 5 . I often look at films in Firefox but feels that the RbP5 are slow - or if it is Firefox memory managing. There...
View Article